Miscellaneous

LTE UE Category & Class Definitions

LTE UE Category & Class Definitions


LTE categories are important because they provide information to the base station, eNB from the user equipment, UE about the capability of the UE.

The UE lets the eNB about its performance by letting it know its category. In this way the eNB is able to provide data at the required level.

In some cases the category might inform the eNB that it requires very low data rates as in the case of Cat 0 or Cat M where the level of performance is directed ore towards remote devices, whereas some may be able to provide very high levels of performance like Cat 6, Cat 7, or even Cat 9.

LTE UE category definitions

There are 9 different LTE UE categories that are defined. As can be seen in the table below, the different LTE categories have a wide range in the supported parameters and performance. LTE category 1, for example does not support MIMO, but LTE UE category five supports 4x4 MIMO.

It is also worth noting that UE class 1 does not offer the performance offered by that of the highest performance HSPA category. Additionally all LTE UE categories are capable of receiving transmissions from up to four antenna ports.

A summary of the different LTE UE category parameters is given in the tables below.


Headline data rates for LTE Categories
LTE UE Category
Link12345678
Downlink10501001503003003001200
Uplink52550507550150600

It can be seen that the headline data rates for category 8 exceed the requiremetns for IMT-Advanced by a considerable margin.

While the headline rates for the different LTE UE categories or UE classes show the maximum data rates achievable, it is worth looking in further detail at the underlying performance characteristics.


UL and DL parameters for LTE UE Categories 1 - 5
LTE Category
ParameterLTE Cat 1LTE Cat 2LTE Cat 3LTE Cat 4LTE Cat 5
Max number of DL-SCH transport block bits received in a TTI10 29651 024102 048150 752302 752
Max number of bits of a DL-SCH block received in a TTI10 29651 02475 37675 376151 376
Total number of soft channel bits250 3681 237 2481 237 2481 827 0723 667 200
Maximum number of supported layers for spatial multiplexing in DL12224
Max number of bits of an UL-SCH transport block received in a TTI5 16025 45651 02451 02475 376
Support for 64-QAM in ULNoNoNoNoYes
UL and DL parameters for LTE UE Categories 6, 7, 8
LTE Category
ParameterLTE Cat 6LTE Cat 7LTE Cat 8
Max number of DL-SCH transport block bits received in a TTI299 552299 5521 200 000
Max number of bits of a DL-SCH block received in a TTITBDTBDTBD
Total number of soft channel bits3 667 200TBDTBD
Maximum number of supported layers for spatial multiplexing in DL
Max number of bits of an UL-SCH transport block received in a TTITBDTBDTBD
Support for 64-QAM in ULNoYes, up to RAN 4Yes

From this it can be seen that the peak downlink data rate for a Category 5 UE using 4x4 MIMO is approximately 300 Mbps, and 150 Mbps for a Category 4 UE using 2x2 MIMO. Also in the Uplink, LTE UE category 5 provides a peak data rate of 75 Mbps using 64-QAM.

Note:
DL-SCH = Downlink shared channel
UL-SCH = Uplink shared channel
TTI = Transmission Time Interval

LTE Category 0

With the considerable level of development being undertaken into the Internet of Things, IoT and general machine to machine, M2M communications, there has been a growing need to develop an LTE category focussed on these applications. Here, much lower data rates are needed, often only in short bursts and an accompanying requirement is for the remote device or machine to be able to draw only low levels of current.

To enable the requirements of these devices to be met using LTE, and new LTE category was developed. Referred to as LTE Category 0, or simply LTE Cat 0, this new category has a reduced performance requirement that meets the needs of many machines while significantly reducing complexity and current consumption. Whilst Category 0 offered a reduced specification, it still complied with the LTE system requirements.


LTE Category 0 Performance Summary
ParameterLTE Cat 0 Performance
Peak downlink rate1 Mbps
Peak uplink rate1 Mbps
Max number of downlink spatial layers1
Number of UE RF chains1
Duplex modeHalf duplex
UE receive bandwidth20 MHz
Maximum UE transmit power23 dBm

The new LTE Cat 0 was introduced in Rel 12 of the 3GPP standards. And it is being advanced in further releases.

One major advantage of LTE Category 0 is that the modem complexity is considerably reduced when compared to other LTE Categories. It is expected that the modem complexity for a Cat 0 modem will be around 50% that of a Category 1 modem.

LTE UE category summary

In the same way that category information is used for virtually all cellular systems from GPRS onwards, so the LTE UE category information is of great importance. While users may not be particularly aware of the category of their UE, it will match the performance an allow the eNB to communicate effectively with all the UEs that are connected to it.

Wireless & Wired Connectivity Topics:
Mobile Communications basics2G GSM3G UMTS4G LTE5GWiFiIEEE 802.15.4DECT cordless phonesNFC- Near Field CommunicationNetworking fundamentalsWhat is the CloudEthernetSerial dataUSBSigFoxLoRaVoIPSDNNFVSD-WAN
Return to Wireless & Wired Connectivity


Watch the video: 4G-LTE parameter Description. (July 2021).